Elite Excavating LLCEliteExcavating LLC
Aerial view of a gravel drive curving up to a house in the country
Asphalt Millings · Almont

Asphalt Millings in Almont, MI

Asphalt millings hauled, spread and graded on long drives, farm lanes and lots in Almont, on a base that has been built to hold them.

  • Free on-site estimates
  • Owner-run by George
  • Based in Capac, MI

Free on-site estimate

Send it over and George calls you back.

Asphalt Millings · Almont

Asphalt Millings in Almont

What millings are good for

Asphalt millings are ground-up old pavement. They pack into a firm, low-dust surface, which makes them a strong fit for long drives, farm lanes and storage or parking lots where paving is more than the job needs.

George hauls them in and spreads them while the machine is on site, graded and crowned like stone.

A village with farm ground on every side

Almont has been here since the 1830s, and the village center still sits at the corner of Van Dyke and St. Clair Street. It is growing again, up about six percent between the 2010 and 2020 censuses, and most of that growth is houses on acreage in Almont Township rather than lots in the village.

When a farm field is split and sold, the first thing the new owner needs is a way to get a truck to the building site. That is where most of George's Almont driveway work starts: a new drive on ground that was corn last year.

M-53 is a state highway

A new drive that opens onto M-53 is on a state highway, so the Michigan Department of Transportation has a say in the approach. On a county road it is the Lapeer County Road Commission. Check with the right office before the drive is cut in.

Stone or millings

Ask for stone and millings on the same estimate so the two can be compared fairly. Which one fits depends on the length of the run, what drives on it and how much dust matters.

Loads come in by truck, so spring weight limits on the roads can push a delivery back a few weeks. On county roads in Lapeer County those are set by the Lapeer County Road Commission.

A price before the work starts

George comes out to Almont, walks the drive or the lot with you and gives you one price before any work starts. The estimate is free, and he runs the machine himself.

Almont is about 14 miles from the yard in Capac. The rest of the work in town is on the Almont page, and the driveway installation & repair page covers the service across St. Clair, Lapeer and Macomb counties.

New stone driveway running up the side of a house
Main service page

Driveways: New drives cut in, tired ones brought back, and lots resurfaced — built on a proper base and crowned so the water runs off the edges.

How it goes

No mystery, no surprise invoice.

Walk the job

George comes out, looks at the ground with you and talks through what it actually needs.

A number before work starts

You get a price for the job in front of you, not a rate and a shrug.

The machine shows up

The equipment arrives when it was said it would, and the work runs start to finish.

Left clean

Ruts knocked down, ground graded, debris gone. The site is finished, not abandoned.

On the ground

Photos of his work.

Every photo here is from a real Elite Excavating job. See more recent work. Or read about the full driveway installation & repair service.

Gravel drive running beside a white house to the back yard
Stone path and side drive between houses
Long gravel farm lane through fields, shown from two angles
Farm drive re-based and crowned
Aerial view of a new gravel drive and turnaround at a country home
Millings compacted into a hard, dust-free surface
Are asphalt millings the same as paving?

No. Millings pack into a firm surface but they are not hot asphalt. They cost less than paving and behave more like a hard gravel.

Do millings get soft in summer?

Some softening on hot days is normal while they are new. They firm up with time and traffic.

Can you resurface a commercial lot?

Yes. Lots have been graded and resurfaced with millings, including storage and parking areas.

Does Elite Excavating do asphalt millings in Almont?

Yes. Almont is about 14 miles from the yard in Capac. George looks at the job himself, gives you a price before any work starts and runs the machine.

More around Almont

Other work he takes on.

Somewhere else? See the full service area or call (989) 702-2426.

Asphalt Millings in other towns

Free estimate

Free estimate in Almont.

Send the details and he will come out, walk the job with you and give you a number before anything starts. If it is easier to talk it through, call him.

Capac, Michigan · St. Clair, Lapeer and Macomb counties

Free on-site estimate

Send it over and George calls you back.

Free estimate. A real number.

Call George. He walks the job with you and gives you a price before any work starts.

Call GeorgeFree Estimate